Medical Processors

     M35A Mammo
     Our series M35A units' compact, dependable and tabletop
     design brings all the benefits of automatic processing to the
     low-volume department or site. Although compact and versatile,
     it is capable of producing high-quality volume from a wide range
     of film grades. The 115-volt operation makes it a great addition
     to private offices, clinics, nuclear, ultrasound and CT suites.

Processing Cycle: 2-1/2 minute processing cycle

Dimensions:

Length: 29.7 inches

Length w/feed tray: 42.4 inches

Width: 26.5 inches

Height: 20.5 inches

Weight: Approximately 253 lbs. with processing tanks filled with solution; 200 lbs. empty

Electrical Requirements: 115 volt; 20 amp, single circuit

Water Requirements: Requires cold water only.

Drain Requirements: Floor drain with a capacity of 10.5 gpm to drain all tanks simultaneously All tanks can be emptied individually. Do not use brass or copper

Dryer Exhaust: Approximately 75 cubic ft/minute

Testing: All refurbished equipment is tested in-house for a Minimum 36-hour period prior to shipment.

Warranty: One year parts warranty.

KODAK X-Omat 2000

This tabletop processor is designed for medium- and low-volume
processing applications such as those for mobile vans, emergency
and trauma departments, and surgical suites. This processor
combines proven reliability and image quality with a selection of
two processing cycles. The rapid cycle (90 seconds) processes
125 34 x 43 cm films an hour and is recommended for general-purpose
radiography films. The standard cycle (120 seconds) processes
100 34 x 43 cm films an hour. The 2000 processor is designed for
220-volt power sources; the 2000A processor for 110-volt operation.

Features

	Rapid and Standard Cycles
	Excellent image quality
	Developer temperature controlled to +/- 0.5.F (+/-0.3.C)
	Easy-to-check replenishment rates
	Flooded replenishment capability for low-volume processing
	Ambient-temperature wash water eliminates water heating and hot-water plumbing
	Automatic standby control reduces power consumption and processor wear
	Easy to service

Optional Accessories:

	Mounting stand
	Lighttight feed tray kit
	Replenisher tank set, 8-gallon
	Flooded replenishment kit

Available Options:

	Stand
	Exhaust Fan Kit

Konica SRX-101A

Maximum Versatility in a Tabletop Design. The SRX-101A tabletop processor offers variable speeds which can be set from within the processor. This allows you to choose the optimum speed to match your processing needs. Konica Minolta's 90 second cycle allows fast developing of all super rapid processable films. 90 Second Super Rapid Processing Cycle / 120 Second Standard Processing Cycle / 180 Second Extended Processing Cycle.

Features
The Konica Minolta SRX-101A processor produces high quality radiographs
with easy operation and is the ideal choice for imaging sites, diagnostic
centers and private practice offices. The SRX-101A processor is perfect
for reliable low volume applications, especially where space is at a premium.
The compact design of the SRX-101A saves valuable space and incorporates
an automatic standby with jog cycle for conserving water and energy.
State-of-the-art technology stabilizes developer and dryer temperatures.
It also offers automatic replenishment.

Series M6B 90-Second Processor

This processor has quickly become the Processor of Choice for General Radiography and Mammography. Built-in electronics, combined with standard upgrades, make it an excellent value as well as a reliable part of your radiology department.

Plumbing
A brand-new molded tank is used to begin the internal refurbishing process. The heat exchangers are sealed in with new seals and compression nuts and new tubing are used to plumb the machine throughout. A new March recirculation pump is installed, as is a Gorman-Rupp bellows replenishment pump. To ensure accurate replenishment rates in the plumbing system, a new incoming water solenoid valve is used to facilitate water conservation and a new developer cooling solenoid is also installed to maintain proper development temperatures.

Temperature Sensing
The M6B has two electronically-controlled temperature sensing systems the dryer and developer temperature control. The dryer is maintained through the use of new thoroughly tested thermistor, new dryer temperature potentiometer and reconditioned dryer heaters. The system is protected with an overtemperature safety thermostat and a new blower motor is used to recirculate the tempered air through the system. The blower assembly (which is rebuilt completely with new bearings, main shaft, squirrel cage and machined pulleys) completes the dryer temperature control section. The developer temperature control system is maintained through the use of a new thermistor, new or used developer heater assembly and is protected by an overtemperature device for safety. The sensing circuit on the PCB100 board monitors and controls all activities. The recirculation pump circulates the developer consistently throughout the system, to ensure uniformity in temperature. Finally, the developer is constantly being filtered through the new filter canister assembly and a new LED display of the developer temperature completes the system.

External Features
All units are finished with new internal plastics and new panel sets. The new "greige" color finish is both an aesthetic and eye-pleasing finish.

Electrical Requirements
This unit requires 240 volts. 30amp. Other electrical configurations can be accommodated upon request.

Water Requirements
Requires cold water only. Other specifications available upon request.

Controlled Testing Environment
TI-BA refurbished processors are tested for a minimum of 36 hours to ensure trouble-free operation prior to shipment to customer locations. All adjustments and calibrations are performed during this period.

Available Options
| Drip Tray | Air Exhaust Kit | Small Chain Dev rack

Electrical
The reused electrical box is completely reconditioned with new relays, circuit breakers and a new main wire harness assembly. All reused parts are thoroughly tested and monitored for reliability. The new or reconditioned PCB 100 Board is used to control all functions of the M6B. The auto standby feature will help conserve power and unnecessary wear and tear on parts, as well as assist the machine in staying ready at the touch of a button.

Drive and Transport
At the heart of the TI-BA M6B are the drive and transport assemblies. The drive assembly is completely refurbished, using a new main drive motor and a completely refurbished main drive assembly (which includes all new bearings, worm gears and shaft). The dryer drive assembly is assembled using all new dryer rollers, dryer studs and belt to complete the assembly. The final and most integral assembly included in the unit is the rack transport assembly. TI-BA uses only the highest quality rollers to assemble each rack included in the system. The M6B transport systems consists of a detector, developer, fixer, wash (silicone), developer/fixer crossover, fixer/wash crossover and squeegee rack assemblies. All of the latest OEM modifications and upgrades are incorporated into all TI-BA transport systems.

Contact MPS X-ray Service in Los Angeles, CA and San Antonio, TX for complete
X-ray Equipment Sales, Service, and Maintenance Solutions.
e-mail: mpsxray@verizon.net

Toll-Free: (800) 339-7298 (909) 599-8439 Fax (909) 599-8606

24 Hour Emergency Service

Calling Hours:
8 a.m.– 5 p.m.
After Hours, Please Leave Voice Mails

Calls will be returned promptly.

Send mail to mpsxray@verizon.net with questions or comments about this web site. Last modified: November 01, 2011

Send mail to mpsxray@verizon.net with questions or comments about this web site.
Last modified: November 01, 2011